- #Icom rs ba1 v2 how to
- #Icom rs ba1 v2 manuals
- #Icom rs ba1 v2 serial
- #Icom rs ba1 v2 manual
- #Icom rs ba1 v2 windows 10
#Icom rs ba1 v2 manuals
Bottom line, you really MUST read the manuals carefully, and re-read them. I don't know if this is ICOM's fault, but the latency will throw you off.ĩ. CW keying is relegated to using your keyboard. Switching these audio devices can lead to painful results unless you write down the drive/mic gain settings for instance.Ĩ. This way, you can switch between a headset or speakers and separate mic, all with AF/Mic gain presets, etc. Icom should include "remote profile settings" for up to 3 different hardware devices connected. You will also want a dynamic DNS service if you hope to use this from afar without a static IP.ħ.
#Icom rs ba1 v2 how to
You NEED to know how to access your firewall and router and this not only includes the box at your QTH, it includes your Windows computer(s). they kinda can, using uPNP, but they don't. I don't blame Icom as much as most of you, they can't sneak into your router and open ports, for instance. Honestly, half of it is in the manual, the other half is "are you an IT guru?". A lot of people have issues with actually getting this stuff to work properly. It's almost as expensive as a used 706 MkIIG hi hi! I have found a cheaper solution that I posted on QRZ, read on.Ħ. If you want to finely control your remote rig like a real rig, there is a very expensive jog/shuttle dial for purchase. This is not Icom's fault totally, I'm being critical, so you are aware of potential improvements or pitfalls.ĥ.
Bottom line: If Icom introduced better audio compression algorithms than u-Law or LPCM (is that even compressed?) then maybe some better performance could be achieved for those of you with slow data connections. You can do this on 4G if you are near a tower and not sharing your connection. You should have a solid 500kbit or hopefully 1mbit stream.
DSL might be sufficient, but you will likely get choppy audio and lag time. You need "good" network bandwidth to pull this all off. This one is not as much as a ding on the app, well, kinda. and another port for my USB-enabled rotator!Ĥ.
A Silex DS-510 ($100) that gives me a control port for Logger/FT8/SSTV etc. I had to purchase a separate (here we go again.) device. If you think you can get by with a virtual port splitter, good luck with that, I've been there and tried to do that with Eltima and VSPE and even West Mountain. If you don't have a middleman-pc and attempt to use a logging or digital mode application, forget it.
#Icom rs ba1 v2 serial
You get only ONE virtual serial port for control. they had to ditch that and re-purchase V2. You get incremental upgrades in the same version (there will be three of those). If you consider other possible accessories to make this all work, you will be out a good chunk of change.Ģ. You have to pay for the software, and it's NOT cheap at $150. Let me start with the negatives, since there ARE some.ġ. I am happy with the way it all works, however. I didn't want to complicate things with another PC, and found that it only made things MORE complicated in the end. There are other options besides RS-BA1 in that case. If you don't have a 7610, 7700 or 7800, you will need a PC between the rig and your remote. This review focuses on "Life without a middleman-PC". This review is purely my opinion, your requirements and operating habits will be different. Game Changer! Freedom and FUN once you survive the BUMPS The tech related how as a six-year old, her grandfather let her talk on ham radio to her uncle in the service in Japan.) (My provider had a note on my account that this was for ham radio.
It's the computers in between that are tricky. My recommendation is to investigate other remote control solutions and be prepared to spend some time and money. I could have stopped there, but I wanted the whole package to work for $150. Ironically, the Team View app provided control of the radio using the RS-BA1 software on the base station radio. Nowhere in any of the four computers I used does that address appear. She was the one to figure out that I needed the IP address of the modem, not the computer. I have a local, family-owned Internet Service Provider with top-drawer customer support.
#Icom rs ba1 v2 manual
The manual guided me to the address of the computer, easy to find if you follow the manual. The biggest issue was the IP address needed to connect to the base station. The manual is really pretty good, but does not capture the steps I needed.
#Icom rs ba1 v2 windows 10
Add to that the way that Windows 10 changes the interface (I'm a Mac guy). Since every router and ISP is different, it is difficult to predict the settings. I spent several months moving back and forth between the base and remote stations (two hours apart) trying to get the settings right especially opening all three port forwardings on 1) the router, 2) the base station modem, and 3) my remote station modem.
0 kommentar(er)
